Home GATE Warfet AEG Control System V1.1
GATE Warfet AEG Control System V1.1
GATE Warfet AEG Control System V1.1
Warehouse Location: Stell36-Bak6
GATE Warfet AEG Control System V1.1
A Mosfet with a lot of functions and external programming through a programming card! Top of the line!
V2, with upgraded software for rapid-auto-precocking.
TACTICAL PROGRAMMING CARD
The outstanding Tactical Programming Card provides you with very easy access to the AEG Controller settings. All you need to do is connect the Tactical Programming Card between the battery and the Controller.
(Specifically for the WARFET!)
Victory in the game is often a matter of fractions of seconds. Thanks to the PRE-COCKING, you gain a trigger reaction similar to a real gun. It allows for initial spring compression, which speeds up the trigger response significantly. You can set the time of PRE-COCKING using the Tactical Programming Card. There are two PRE-COCKING MODES:
1) AUTO MODE – the spring is automatically compressed after each shot.
2) TRIGGER MODE – the first trigger action compresses the spring, and the second trigger action fires the shot.
Please note: using PRE-COCKING increases wear and tear on the gearbox. PRE-COCKING is designed for SEMI mode. In the AUTO mode, it can result in blank shots.
Super-easy installation, just plug and play. No soldering required. All you need to do is connect the battery and the rifle to the AEG Controller.
The burst enables you to shoot a pre-determined number of BBs (1-5 rounds), which is very useful in MILSLIM and when using low-caps. You can transform AUTO MODE to BURST MODE or SEMI MODE to BURST MODE*. The Tactical Programming Card allows you to set the burst time. The AEG Controller automatically corrects the burst time according to the voltage level of the battery.
*SEMI to BURST in modified installations only.
CONFIGURABLE FIRE SELECTOR
The function gives you the option to program your fire selector. There are five operating modes:
- STOCK WIRING SEMI/AUTO
- STOCK WIRING SEMI/BURST
- MODIFIED WIRING SEMI/AUTO
- MODIFIED WIRING SEMI/BURST
- MODIFIED WIRING BURST/AUTO
RATE OF FIRE CONTROL
It enables lossless reduction of the rifle’s rate of fire, so you can use strong LiPo batteries, and still have ROF like in a real gun.
We all know how vital the fast trigger response is during combat. This is why we have developed the Smart Trigger function. It enables you to achieve a faster trigger response. It works with the ROF Control system. During the first shot, the microprocessor sets the ROF Control to 100%. After the first shot, it switches to a previously programmed value (e.g. 50%). As a consequence, the first shot is fired at a full rate of fire, and subsequent shots at a reduced ROF. The best results can be achieved by using a battery with a higher than standard voltage. For example, if you use a 7.4V battery, you can replace it with 11.1V. In this way, you will achieve a faster trigger response with the same rate of fire as with a standard battery. The Smart Trigger is most effective when the Burst time is set at 3 rounds.
Protection against Over-Discharge of the Battery Modern LiPo and LiFe batteries are very sensitive to over-discharge. If you do not want to damage the battery and you care about its service life, this protection is indispensable. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, the Controller will not allow firing.
The new AEG Controller should never let you down on the battlefield. It is the best electronic fuse. The AEG Controller has a true current sensor. A combination of current, voltage and temperature measurements makes your AEG installation highly reliable. If your rifle becomes jammed, the SMART FUSE protects motor and battery against damage. Overheating, overloading or short-circuiting of the electrical system should not damage the Controller.
ON/OFF ACTIVE BRAKE
The Controller provides you with the opportunity to decide if you want to use the Active Brake function. If you do not need this, you can turn it off easily. It will lead to improving the lifespan of your motor.
Do you care about realism? Would you like to increase the life of the gearbox? Does your rifle have such a high rate of fire that you are not able to make a single shot? The Active Brake sorts things out. In SEMI Mode, the brake does not allow for compressing a piston after a shot. The piston will stop in the front position which eliminates unnecessary stresses, increasing the service life of the gearbox and its parts. This is important, especially with an AEG power upgrade. After releasing the trigger, the rifle immediately stops firing. So, you gain more realism and, additionally, you do not waste your precious ammunition.
Do you want to achieve a higher rate of fire and faster trigger response? Are you planning a power upgrade of your rifle? In that case, you need a MOSFET.
It targets the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. As a result, you gain a higher rate of fire of the rifle and a faster trigger response, and the contacts are protected against burn out.
This provides full compatibility with the micro-switches. It ensures full resistance to contact bounce (vibration). You gain a bigger ROF, a faster trigger response and your MOSFET is less prone to overheating.
It allows you to quickly check whether the AEG Controller works properly. If you have problems with your AEG, the BUILT-IN SELF-TEST allows you to check that the problem is not caused by the Controller.
3RD GENERATION MOSFET
The advent of modern transistors and microcontroller has enabled GATE to create the smallest and most reliable AEG Controller on the market.
DARK MODE allows you to turn off the green LED which lights up when a gun is firing. This function is especially useful during night games.
Thanks to its special conformal coating, it is resistant to atmospheric conditions (Military Specification MIL-V-173C).
14.8V LI-PO READY
The system can be used with batteries up to 14.8V LI-PO. Minimum operating voltage is 3V and maximum voltage is 17V.
In the case of a hardwired installation, the Controller draws the power from the battery directly to the motor, bypassing the mechanical trigger contacts. This requires a modification of the AEG installation.
MINI TAMIYA READY
Thanks to the Mini Tamiya Adapters included in kit, you will be able to smoothly connect WARFET to your original installation.
It makes easier starting your adventure with WARFET. The quickstart contains basic information and hints.
* User-Friendly Tactical Programming Card
* Working voltage: 3 - 17V
* Suited for the most powerfull AEG's and batteries. (Suited for 14.8V, 5000mAh 60c batteries and is even tested with car batteries!)
* Easy to install
* Extended protection
* Very low standby power usage (0.2mA)
* Very low resistance (2mΩ)
* Dimentions: 56x20x9 mm
* DEANS-T Connectors
- Tactical Programming Card
- WARFET AEG Controller
- Extra Deans-T Connectors kit
- Mini Tamiya Adaptor kit
- Single signal wire for trigger contacts
- Double signal wire for trigger contacts
- Quick start guide
For more technical information, please click here!